Cellular network
From Wikipedia, the free encyclopedia
 | The tone or style of this article may not be appropriate for Wikipedia. Specific concerns may be found on the talk page. See Wikipedia's guide to writing better articles for suggestions. (December 2007) |
A cellular network is a radio network made up of a number of radio cells (or just cells) each served by a fixed transmitter, known as a cell site or base station. These cells are used to cover different areas in order to provide radio coverage over a wider area than the area of one cell. Cellular networks are inherently asymmetric with a set of fixed main transceivers each serving a cell and a set of distributed (generally, but not always, mobile) transceivers which provide services to the network's users.
Cellular networks offer a number of advantages over alternative solutions:
- increased capacity
- reduced power usage
- better coverage
A good (and simple) example of a cellular system is an old taxi driver's radio system where the taxi company will have several transmitters based around a city each operated by an individual operator.
[edit] General characteristics
 | This article requires authentication or verification by an expert. Please assist in recruiting an expert or improve this article yourself. See the talk page for details. (December 2008) |
The primary requirement for a network to succeed as a cellular network is for it to have developed a standardised method for each distributed station to distinguish the signal emanating from its own transmitter from the signals received from other transmitters. Presently, there are two standardised solutions to this issue, frequency division multiple access (FDMA) and code division multiple access (CDMA).
FDMA works by using varying frequencies for each neighbouring cell. By tuning to the frequency of a chosen cell the distributed stations can avoid the signal from other cells. The principle of CDMA is more complex, but achieves the same result; the distributed transceivers can select one cell and listen to it. Other available methods of multiplexing such as polarization division multiple access (PDMA) and time division multiple access (TDMA) cannot be used to separate signals from one cell to the next since the effects of both vary with position and this would make signal separation practically impossible. Time division multiple access, however, is used in combination with either FDMA or CDMA in a number of systems to give multiple channels within the coverage area of a single cell.
In the case of the aforementioned taxi company, each radio has a knob. The knob acts as a channel selector and allows the radio to tune to different frequencies. As the drivers move around, they change from channel to channel. The drivers know which frequency covers approximately what area. When they don't get a signal from the transmitter, they also try other channels until they find one which works. The taxi drivers only speak one at a time, as invited by the operator (in a sense TDMA).
[edit] Broadcast messages and paging
Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles, commonly, for example in mobile telephony systems, the most important use of broadcast information is to set up channels for one to one communication between the mobile transreceiver and the base station. This is called paging.
The details of the process of paging vary somewhat from network to network, but normally we know a limited number of cells where the phone is located (this group of cells is called a Location Area in the GSM or UMTS system, or Routing Area if a data packet session is involved). Paging takes place by sending the broadcast message to all of those cells. Paging messages can be used for information transfer. This happens in pagers, in CDMA systems for sending SMS messages, and in the UMTS system where it allows for low downlink latency in packet-based connections.
[edit] Frequency reuse
The increased capacity in a cellular network, compared with a network with a single transmitter, comes from the fact that the same radio frequency can be reused in a different area for a completely different transmission. If there is a single plain transmitter, only one transmission can be used on any given frequency. Unfortunately, there is inevitably some level of interference from the signal from the other cells which use the same frequency. This means that, in a standard FDMA system, there must be at least a one cell gap between cells which reuse the same frequency.
The frequency reuse factor is the rate at which the same frequency can be used in the network. It is 1/K (or K according to some books) where K is the number of cells which cannot use the same frequencies for transmission. Common values for the frequency reuse factor are 1/3, 1/4, 1/7, 1/9 and 1/12 (or 3, 4, 7, 9 and 12 depending on notation).
In case of N sector antennas on the same base station site, each with different direction, the base station site can serve N different sectors. N is typically 3. A reuse pattern of N/K denotes a further division in frequency among N sector antennas per site. Some current and historical
Tidak ada komentar:
Posting Komentar